Plasma nesting differs from laser nesting in two ways that matter: kerf and part spacing need to be thickness- and amperage-aware rather than one fixed margin, and pierce count (not just cut length) drives both time and cost. The nester doesn't talk to the table directly either way — on a SheetCAM-based setup it hands over a DXF, and SheetCAM generates the G-code for FireControl, Mach3 or LinuxCNC. Zorocut nests true-shape with part-in-part fitting and exports that DXF; it doesn't do common-line cutting yet. Deepnest is free and true-shape but has open issues with part-in-part and edge margins. Lantek sells CAD/CAM suites across oxycut, plasma, laser and waterjet; SigmaNEST is priced for industrial production. Neither publishes a self-serve price.
What's actually different about plasma
A laser nester's spacing defaults don't transfer straight to plasma. Kerf varies more with amperage and consumable wear, so the gap between parts needs to scale with thickness rather than use one fixed margin — see kerf width for laser and plasma and part spacing. Each pierce takes time before the torch is actually cutting, so a nest with more, smaller parts costs more in pierces even at the same total cut length — see pierce time for laser and plasma.
What a plasma nester needs to do
- True-shape nesting with part-in-part fitting, not just rectangle packing.
- Spacing you can set per material and thickness, not one fixed margin for the whole job.
- A clean DXF out the other end — closed contours, correct units, no duplicate lines — because the CAM program that turns it into G-code (SheetCAM, for most hobby and small plasma tables) won't fix a bad import, it'll just cut it badly.
- A pierce count you can see before you cut, since that's one of the main things driving plasma job cost beyond the plate itself.
What Zorocut does and doesn't do here
Zorocut Nest does true-shape nesting with part-in-part fitting and rotation, runs the pre-cut DXF checks (open contours, duplicate lines, units), and exports a DXF that SheetCAM imports — SheetCAM then writes the G-code for FireControl, Mach3 or LinuxCNC; FireControl itself cannot open a DXF directly. See DXF from Zorocut to SheetCAM/FireControl and the SheetCAM machine page (status: beta). Zorocut does not do common-line cutting (sharing one cut line between two adjacent straight-edged parts) yet — see what common-line cutting is for the concept if you're evaluating that specifically. Remnant tracking today covers strips and L-shapes, not arbitrary leftover outlines.
Where the free and open-source options stand
Deepnest is the true-shape nester most plasma shops try first because it's free. The maintained fork, deepnest-next, is MIT-licensed outside one GPLv3 module, but its open issues are the kind a shop notices in production: part-in-part fitting fails (#170), there's no edge margin setting (#167), curves get approximated as straight segments (#66, #160). No quote, no remnant tracking. Full comparison on Zorocut vs Deepnest.
Where the CAD/CAM suites stand
Lantek sells Expert Cut, a CAD/CAM nesting suite spanning oxycut, plasma, laser and waterjet, plus iQuoting, a separate browser quoting tool — both priced on request, with no stated free tier for iQuoting. SigmaNEST is built and priced for industrial production runs rather than a single small shop. Neither is a lightweight point nester; if you're sizing one of these against Zorocut, see Zorocut vs Lantek and Zorocut vs SigmaNEST.
Pricing the job after the nest
Pierce count and cut length from the nest feed straight into cost. How to price plasma cutting walks through the formula, and the plasma cutting price calculator runs it on a worked example so you're not guessing at pierce delay or speed by amperage.
Run a plasma job through the price calculator and see what it assumes for pierce count and speed before you cut.
Nest a DXF onlineFrequently asked questions
Does nesting software work the same for plasma as for laser?
The nesting logic (true-shape, part-in-part, rotation) is the same; the spacing and pierce-cost assumptions aren't. Plasma needs wider, thickness-aware margins and treats pierce count as a cost driver in its own right — see the kerf and pierce guides above.
Does Zorocut export a DXF my plasma table's CAM software can use?
Yes — Zorocut nests and runs the pre-cut DXF checks, then exports a DXF that SheetCAM and similar CAM programs import. SheetCAM (not Zorocut) turns that into the G-code your controller runs.
Does nesting reduce the number of pierces?
Tight part-in-part nesting cuts travel and wasted material, but pierce count still tracks the number of distinct parts and internal holes in the job, not how they're arranged on the sheet. See pierce time for laser and plasma.
